Sorry for the mix up yesterday of my production and testing machine. i ran all the terminal commands suggested, added the entry into modprobe.preload and wound still dont have a working device. Below is the output of dmesg which Does see the device.Still would appreciate any help.
dmesg
Linux version 2.6.38.8-pclos2.bfs (root@thenudiebar) (gcc version 4.5.2 (GCC) ) #1 SMP PREEMPT Fri Jul 8 02:57:34 CDT 2011
BIOS-provided physical RAM map:
Malformed early option 'acpi'
Notice: NX (Execute Disable) protection cannot be enabled: non-PAE kernel!
DMI 2.4 present.
DMI: System manufacturer System Product Name/M2N-E SLI, BIOS ASUS M2N-E SLI ACPI BIOS Revision 1204 09/18/2008
e820 update range: 0000000000000000 - 0000000000010000 (usable) ==> (reserved)
e820 remove range: 00000000000a0000 - 0000000000100000 (usable)
last_pfn = 0x7fee0 max_arch_pfn = 0x100000
MTRR default type: uncachable
MTRR fixed ranges enabled:
00000-9FFFF write-back
A0000-BFFFF uncachable
C0000-C7FFF write-protect
C8000-FFFFF uncachable
MTRR variable ranges enabled:
0 base 0000000000 mask FF80000000 write-back
1 base 007FF00000 mask FFFFF00000 uncachable
pnp: PnP ACPI init
ACPI: bus type pnp registered
pnp 00:00: Plug and Play ACPI device, IDs PNP0a08 PNP0a03 (active)
system 00:01: Plug and Play ACPI device, IDs PNP0c02 (active)
IP route cache hash table entries: 32768 (order: 5, 131072 bytes)
TCP established hash table entries: 131072 (order: 8, 1048576 bytes)
TCP bind hash table entries: 65536 (order: 7, 524288 bytes)
TCP: Hash tables configured (established 131072 bind 65536)
TCP reno registered
UDP hash table entries: 512 (order: 2, 16384 bytes)
UDP-Lite hash table entries: 512 (order: 2, 16384 bytes)
NET: Registered protocol family 1
pci 0000:00:00.0: Found enabled HT MSI Mapping
pci 0000:00:0b.0: Found disabled HT MSI Mapping
pci 0000:00:00.0: Found enabled HT MSI Mapping
pci 0000:00:0b.0: Linking AER extended capability
pci 0000:00:00.0: Found enabled HT MSI Mapping
pci 0000:00:0c.0: Found disabled HT MSI Mapping
pci 0000:00:00.0: Found enabled HT MSI Mapping
pci 0000:00:0c.0: Linking AER extended capability
pci 0000:00:00.0: Found enabled HT MSI Mapping
pci 0000:00:0d.0: Found disabled HT MSI Mapping
pci 0000:00:00.0: Found enabled HT MSI Mapping
pci 0000:00:0d.0: Linking AER extended capability
pci 0000:00:00.0: Found enabled HT MSI Mapping
pci 0000:00:0e.0: Found disabled HT MSI Mapping
pci 0000:00:00.0: Found enabled HT MSI Mapping
pci 0000:00:0e.0: Linking AER extended capability
pci 0000:05:00.0: Boot video device
PCI: CLS 32 bytes, default 64
Trying to unpack rootfs image as initramfs...
Freeing initrd memory: 6684k freed
apm: BIOS version 1.2 Flags 0x07 (Driver version 1.16ac)
apm: disabled - APM is not SMP safe.
audit: initializing netlink socket (disabled)
type=2000 audit(1319966844.363:1): initialized
highmem bounce pool size: 64 pages
HugeTLB registered 4 MB page size, pre-allocated 0 pages
VFS: Disk quotas dquot_6.5.2
Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
msgmni has been set to 1721
Block layer SCSI generic (bsg) driver version 0.4 loaded (major 253)
io scheduler noop registered
io scheduler deadline registered
io scheduler cfq registered (default)
pcieport 0000:00:0b.0: setting latency timer to 64
pcieport 0000:00:0b.0: irq 40 for MSI/MSI-X
pcieport 0000:00:0c.0: setting latency timer to 64
pcieport 0000:00:0c.0: irq 41 for MSI/MSI-X
pcieport 0000:00:0d.0: setting latency timer to 64
pcieport 0000:00:0d.0: irq 42 for MSI/MSI-X
pcieport 0000:00:0e.0: setting latency timer to 64
pcieport 0000:00:0e.0: irq 43 for MSI/MSI-X
vesafb: framebuffer at 0xd0000000, mapped to 0xf7c80000, using 3072k, total 262144k
vesafb: mode is 1024x768x16, linelength=2048, pages=1
vesafb: protected mode interface info at c000:cb60
vesafb: pmi: set display start = c00ccb96, set palette = c00ccc00
vesafb: pmi: ports = 3b4 3b5 3ba 3c0 3c1 3c4 3c5 3c6 3c7 3c8 3c9 3cc 3ce 3cf 3d0 3d1 3d2 3d3 3d4 3d5 3da
vesafb: scrolling: redraw
vesafb: Truecolor: size=0:5:6:5, shift=0:11:5:0
Console: switching to colour frame buffer device 128x48
fb0: VESA VGA frame buffer device
ERST: Table is not found!
isapnp: Scanning for PnP cards...
Serial: 8250/16550 driver, 4 ports, IRQ sharing enabled
serial8250: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
00:09: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
Linux agpgart interface v0.103
brd: module loaded
i8042: PNP: PS/2 Controller [PNP0303:PS2K,PNP0f13:PS2M] at 0x60,0x64 irq 1,12
rtc_cmos 00:05: RTC can wake from S4
rtc_cmos 00:05: rtc core: registered rtc_cmos as rtc0
rtc0: alarms up to one year, y3k, 242 bytes nvram, hpet irqs
cpuidle: using governor ladder
cpuidle: using governor menu
TCP cubic registered
Registering the dns_resolver key type
Using IPI No-Shortcut mode
input: AT Translated Set 2 keyboard as /devices/platform/i8042/serio0/input/input0
psmouse serio1: ID: 10 00 64
isapnp: No Plug & Play device found
input: ImPS/2 Generic Wheel Mouse as /devices/platform/i8042/serio1/input/input1
registered taskstats version 1
rtc_cmos 00:05: setting system clock to 2011-10-30 09:27:25 UTC (1319966845)
BIOS EDD facility v0.16 2004-Jun-25, 2 devices found
Freeing unused kernel memory: 512k freed
BFS CPU scheduler v0.401 by Con Kolivas.
SCSI subsystem initialized
libata version 3.00 loaded.
sata_nv 0000:00:07.0: version 3.5
ACPI: PCI Interrupt Link [APSI] enabled at IRQ 23
sata_nv 0000:00:07.0: PCI INT A -> Link[APSI] -> GSI 23 (level, low) -> IRQ 23
sata_nv 0000:00:07.0: setting latency timer to 64
ata1: SATA max UDMA/133 cmd 0x9f0 ctl 0xbf0 bmdma 0xd400 irq 23
ata2: SATA max UDMA/133 cmd 0x970 ctl 0xb70 bmdma 0xd408 irq 23
ACPI: PCI Interrupt Link [APSJ] enabled at IRQ 22
sata_nv 0000:00:08.0: PCI INT A -> Link[APSJ] -> GSI 22 (level, low) -> IRQ 22
sata_nv 0000:00:08.0: setting latency timer to 64
usbcore: registered new interface driver usbfs
usbcore: registered new interface driver hub
usbcore: registered new device driver usb
<30>udev[113]: starting version 167
k8temp 0000:00:18.3: Temperature readouts might be wrong - check erratum #141
ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
ACPI: PCI Interrupt Link [APCF] enabled at IRQ 21
ohci_hcd 0000:00:02.0: PCI INT A -> Link[APCF] -> GSI 21 (level, low) -> IRQ 21
ohci_hcd 0000:00:02.0: setting latency timer to 64
ohci_hcd 0000:00:02.0: OHCI Host Controller
ohci_hcd 0000:00:02.0: new USB bus registered, assigned bus number 1
ohci_hcd 0000:00:02.0: irq 21, io mem 0xfe02f000
usb usb1: New USB device found, idVendor=1d6b, idProduct=0001
usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
usb usb1: Product: OHCI Host Controller
usb usb1: Manufacturer: Linux 2.6.38.8-pclos2.bfs ohci_hcd
usb usb1: SerialNumber: 0000:00:02.0
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 9 ports detected
input: Power Button as /devices/LNXSYSTM:00/device:00/PNP0C0C:00/input/input2
IT8716 SuperIO detected.
parport_pc 00:0a: reported by Plug and Play ACPI
parport0: PC-style at 0x378, irq 7 [PCSPP,TRISTATE,EPP]
ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
Warning! ehci_hcd should always be loaded before uhci_hcd and ohci_hcd, not after Could this be a problem and where would/how to edit
ACPI: PCI Interrupt Link [APCL] enabled at IRQ 20
ehci_hcd 0000:00:02.1: PCI INT B -> Link[APCL] -> GSI 20 (level, low) -> IRQ 20
ehci_hcd 0000:00:02.1: setting latency timer to 64
ehci_hcd 0000:00:02.1: EHCI Host Controller
ehci_hcd 0000:00:02.1: new USB bus registered, assigned bus number 2
ehci_hcd 0000:00:02.1: debug port 1
ehci_hcd 0000:00:02.1: cache line size of 32 is not supported
ehci_hcd 0000:00:02.1: irq 20, io mem 0xfeb00000
ACPI: PCI Interrupt Link [APC4] enabled at IRQ 19
xhci_hcd 0000:04:00.0: PCI INT A -> Link[APC4] -> GSI 19 (level, low) -> IRQ 19
xhci_hcd 0000:04:00.0: setting latency timer to 64
xhci_hcd 0000:04:00.0: xHCI Host Controller
xhci_hcd 0000:04:00.0: new USB bus registered, assigned bus number 3
xhci_hcd 0000:04:00.0: irq 19, io mem 0xfdeff000
xhci_hcd 0000:04:00.0: Failed to enable MSI-X
xhci_hcd 0000:04:00.0: irq 44 for MSI/MSI-X
usb usb3: No SuperSpeed endpoint companion for config 1 interface 0 altsetting 0 ep 129: using minimum values
usb usb3: New USB device found, idVendor=1d6b, idProduct=0003
usb usb3: New USB device strings: Mfr=3, Product=2, SerialNumber=1
usb usb3: Product: xHCI Host Controller
usb usb3: Manufacturer: Linux 2.6.38.8-pclos2.bfs xhci_hcd
usb usb3: SerialNumber: 0000:04:00.0
xHCI xhci_add_endpoint called for root hub
xHCI xhci_check_bandwidth called for root hub
hub 3-0:1.0: USB hub found
hub 3-0:1.0: 5 ports detected
Floppy drive(s): fd0 is 1.44M
ppdev: user-space parallel port driver
FDC 0 is a post-1991 82077
ACPI: PCI Interrupt Link [APC2] enabled at IRQ 17
firewire_ohci 0000:01:01.0: PCI INT A -> Link[APC2] -> GSI 17 (level, low) -> IRQ 17
usb 1-7: new full speed USB device using ohci_hcd and address 2
ehci_hcd 0000:00:02.1: USB 2.0 started, EHCI 1.00
usb usb2: New USB device found, idVendor=1d6b, idProduct=0002
usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1
usb usb2: Product: EHCI Host Controller
usb usb2: Manufacturer: Linux 2.6.38.8-pclos2.bfs ehci_hcd
usb usb2: SerialNumber: 0000:00:02.1
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 9 ports detected
ACPI: resource nForce2_smbus [io 0x4c00-0x4c3f] conflicts with ACPI region SM00 [io 0x4c00-0x4c05]
ACPI: If an ACPI driver is available for this device, you should use it instead of the native driver
i2c i2c-0: nForce2 SMBus adapter at 0x4c40
forcedeth: Reverse Engineered nForce ethernet driver. Version 0.64.
ACPI: PCI Interrupt Link [APCH] enabled at IRQ 23
forcedeth 0000:00:0a.0: PCI INT A -> Link[APCH] -> GSI 23 (level, low) -> IRQ 23
forcedeth 0000:00:0a.0: setting latency timer to 64
firewire_ohci: Added fw-ohci device 0000:01:01.0, OHCI v1.10, 4 IR + 8 IT contexts, quirks 0x11
hub 1-0:1.0: unable to enumerate USB device on port 7
thermal LNXTHERM:00: registered as thermal_zone0
ACPI: Thermal Zone [THRM] (40 C)
ACPI: acpi_idle registered with cpuidle
sr0: scsi3-mmc drive: 48x/48x writer dvd-ram cd/rw xa/form2 cdda tray
cdrom: Uniform CD-ROM driver Revision: 3.20
sr 0:0:0:0: Attached scsi CD-ROM sr0
Linux video capture interface: v2.00
sr 0:0:0:0: Attached scsi generic sg0 type 5
sd 1:0:0:0: Attached scsi generic sg1 type 0
sd 2:0:0:0: Attached scsi generic sg2 type 0
usb 3-1: new high speed USB device using xhci_hcd and address 2
xhci_hcd 0000:04:00.0: WARN: short transfer on control ep
xhci_hcd 0000:04:00.0: WARN: short transfer on control ep
usb 3-1: New USB device found, idVendor=2109, idProduct=0811
usb 3-1: New USB device strings: Mfr=0, Product=1, SerialNumber=0
usb 3-1: Product: USB2.0 Hub
hub 3-1:1.0: USB hub found
xhci_hcd 0000:04:00.0: WARN: short transfer on control ep
hub 3-1:1.0: 4 ports detected
forcedeth 0000:00:0a.0: ifname eth0, PHY OUI 0x1374 @ 0, addr 00:1d:60:20:b1:53
forcedeth 0000:00:0a.0: highdma csum gbit lnktim desc-v3
cx23885 driver version 0.0.2 loaded
cx23885 0000:02:00.0: PCI INT A -> Link[APC2] -> GSI 17 (level, low) -> IRQ 17
CORE cx23885[0]: subsystem: 0070:7801, board: Hauppauge WinTV-HVR1800 [card=2,autodetected]
firewire_core: created device fw0: GUID 0011d8000158aa30, S400
firewire_core: phy config: card 0, new root=ffc1, gap_count=5
usb 2-8: new high speed USB device using ehci_hcd and address 3
usb 2-8: New USB device found, idVendor=058f, idProduct=6364
usb 2-8: New USB device strings: Mfr=1, Product=2, SerialNumber=3
usb 2-8: Product: Mass Storage Device
usb 2-8: Manufacturer: Generic
usb 2-8: SerialNumber: 058F63646476
IR NEC protocol handler initialized
IR RC5(x) protocol handler initialized
tveeprom 1-0050: Hauppauge model 78521, rev C1E9, serial# 3147097
tveeprom 1-0050: MAC address is 00:0d:fe:30:05:59
tveeprom 1-0050: tuner model is Philips 18271_8295 (idx 149, type 54)
tveeprom 1-0050: TV standards NTSC(M) ATSC/DVB Digital (eeprom 0x88)
tveeprom 1-0050: audio processor is CX23887 (idx 42)
tveeprom 1-0050: decoder processor is CX23887 (idx 37)
tveeprom 1-0050: has radio
cx23885[0]: hauppauge eeprom: model=78521
usb 1-7: new full speed USB device using ohci_hcd and address 3
usb 1-7: New USB device found, idVendor=0d8c, idProduct=0201
usb 1-7: New USB device strings: Mfr=0, Product=2, SerialNumber=0
usb 1-7: Product: PnP Audio Device
IR RC6 protocol handler initialized
cx25840 3-0044: cx23887 A/V decoder found @ 0x88 (cx23885[0])
Initializing USB Mass Storage driver...
scsi6 : usb-storage 2-8:1.0
usbcore: registered new interface driver usb-storage
USB Mass Storage support registered.
usbcore: registered new interface driver uas
generic-usb: probe of 0003:058F:6364.0001 failed with error -22
usbcore: registered new interface driver usbhid
usbhid: USB HID core driver
ACPI: PCI Interrupt Link [APC1] enabled at IRQ 16
CA0106 0000:01:06.0: PCI INT A -> Link[APC1] -> GSI 16 (level, low) -> IRQ 16
snd-ca0106: Model 100a Rev 00000000 Serial 100a1102
IR JVC protocol handler initialized
IR Sony protocol handler initialized
lirc_dev: IR Remote Control driver registered, major 250
IR LIRC bridge handler initialized
nvidia: module license 'NVIDIA' taints kernel.
Disabling lock debugging due to kernel taint
usbcore: registered new interface driver snd-usb-audio
cx25840 3-0044: loaded v4l-cx23885-avcore-01.fw firmware (16382 bytes)
i2c-core: driver [tuner] using legacy suspend method
i2c-core: driver [tuner] using legacy resume method
tuner 2-0042: chip found @ 0x84 (cx23885[0])
tda829x 2-0042: could not clearly identify tuner address, defaulting to 60
tda18271 2-0060: creating new instance
scsi 6:0:0:0: Direct-Access Generic- SD/MMC 1.00 PQ: 0 ANSI: 0
sd 6:0:0:0: Attached scsi generic sg3 type 0
scsi 6:0:0:1: Direct-Access Generic- Compact Flash 1.01 PQ: 0 ANSI: 0
sd 6:0:0:1: Attached scsi generic sg4 type 0
scsi 6:0:0:2: Direct-Access Generic- SM/xD-Picture 1.02 PQ: 0 ANSI: 0
sd 6:0:0:2: Attached scsi generic sg5 type 0
scsi 6:0:0:3: Direct-Access Generic- MS/MS-Pro 1.03 PQ: 0 ANSI: 0 CCS
sd 6:0:0:3: Attached scsi generic sg6 type 0
TDA18271HD/C1 detected @ 2-0060
sd 6:0:0:0: [sdc] Attached SCSI removable disk
sd 6:0:0:1: [sdd] Attached SCSI removable disk
sd 6:0:0:3: [sdf] Attached SCSI removable disk
sd 6:0:0:2: [sde] Attached SCSI removable disk
ACPI: PCI Interrupt Link [APC3] enabled at IRQ 18
nvidia 0000:05:00.0: PCI INT A -> Link[APC3] -> GSI 18 (level, low) -> IRQ 18
nvidia 0000:05:00.0: setting latency timer to 64
vgaarb: device changed decodes: PCI:0000:05:00.0,olddecodes=io+mem,decodes=none:owns=io+mem
NVRM: loading NVIDIA UNIX x86 Kernel Module 285.05.09 Fri Sep 23 18:53:08 PDT 2011
tda829x 2-0042: type set to tda8295+18271
firewire_core: created device fw1: GUID 0010b9021142ec53, S400, 1 config ROM retries
scsi7 : SBP-2 IEEE-1394
firewire_sbp2: fw1.0: logged in to LUN 0000 (0 retries)
scsi 7:0:0:0: Direct-Access Maxtor OneTouch 0121 PQ: 0 ANSI: 4
sd 7:0:0:0: Attached scsi generic sg7 type 0
sd 7:0:0:0: [sdg] 976773168 512-byte logical blocks: (500 GB/465 GiB)
sd 7:0:0:0: [sdg] Write Protect is off
sd 7:0:0:0: [sdg] Mode Sense: 2d 08 00 00
sd 7:0:0:0: [sdg] Got wrong page
sd 7:0:0:0: [sdg] Assuming drive cache: write through
sd 7:0:0:0: [sdg] Got wrong page
sd 7:0:0:0: [sdg] Assuming drive cache: write through
cx23885[0]/0: registered device video0 [v4l2]
cx23885[0]: registered device video1 [mpeg]
cx23885_dvb_register() allocating 1 frontend(s)
cx23885[0]: cx23885 based dvb card
sdg: sdg1 sdg2
sd 7:0:0:0: [sdg] Got wrong page
sd 7:0:0:0: [sdg] Assuming drive cache: write through
sd 7:0:0:0: [sdg] Attached SCSI disk
MT2131: successfully identified at address 0x61
DVB: registering new adapter (cx23885[0])
DVB: registering adapter 0 frontend 0 (Samsung S5H1409 QAM/8VSB Frontend)...
cx23885_dev_checkrevision() Hardware revision = 0xb1
cx23885[0]/0: found at 0000:02:00.0, rev: 15, irq: 17, latency: 0, mmio: 0xfdc00000
cx23885 0000:02:00.0: setting latency timer to 64
cx23885 0000:02:00.0: irq 45 for MSI/MSI-X
kvm: Nested Virtualization enabled
fuse init (API version 7.16)
